Anti-adhesive composition for preventing adhesion to polyurethane foam molds: thermal insulation shells, panels, integral polyurethanes, decorative products.
Packaging:
barrels 150 kg and 35 kg*;
bucket or canister 5 kg* and 10 kg*.
* price for small packaging +10 rubles/kg.
Himtrust AC-10/SM — is an anti-adhesive composition made from wax, paraffins, and silicones in organic solvents.
| Parameter | Value |
| Appearance | Clear or light-yellow liquid dispersion |
| Mass fraction of non-volatile substances at 125°C for 1 hour, %, not less than | 10 |
| Dynamic viscosity at 40°C, mPa·s, not more than | 100 |
| Density, kg/m3 | 650–750 |
When Himtrust AC-10/SM adhesive grease comes into contact with the skin, it may cause irritation, dryness, and flaking. If it comes into contact with the eyes, it can lead to irritation, redness, and tearing. Inhalation may irritate the mucous membranes of the upper respiratory tract.
Before starting work:
Himtrust AC-10/SM lubricant is a flammable liquid. There should be no sources of fire or sparks in the working area. The workspace should be equipped with exhaust ventilation and fire extinguishing equipment. Use personal protective equipment: special clothing, gloves, footwear, and protective goggles.
If Himtrust AC-10/SM lubricant comes into contact with exposed skin areas, it should be removed with a cloth and washed with warm soapy water. In case of skin reactions, seek medical attention. If it comes into contact with the eyes, rinse them immediately with a large amount of running water for 5-10 minutes, then seek medical attention.
Before starting the work:
| № | Problem | Solutions |
| 1 | Adhesion of polyurethane to the mold. | Clean the mold, reapply Himtrust AC-10/SM lubricant. |
The components of the PU system are transported by all means of transport in closed vehicles, following the rules for transporting goods applicable to each mode of transport, ensuring the integrity of the packaging and its secure fixation to prevent damage and leakage.
Store the components in closed warehouses in their original sealed packaging in conditions that prevent moisture ingress.
Storage temperature: from −60°C to +30°C.
Shelf life when recommended conditions are met: 12 months.
During storage, the viscosity of the lubricant may increase. Dilution of the lubricant with Neftas solvent is allowed, but not more than 5% of the remaining volume.
After the expiration of the shelf life, the anti-adhesive lubricant should be checked for compliance with technical characteristics and, if suitability is confirmed, it can also be used as intended.
Component A - KAT-40, component B: Wannate PM-200 etc.
Component A - KAT-40(slower), component B: Wannate PM-200 etc.
Component A - KAT-40F, component B: Wannate PM-200 etc.
For anti-adhesion coating in molds. Mass fraction of non-volatile substances not less than 5%.
For anti-adhesive coating in molds. The mass fraction of non-volatile substances is not less than 15%.
For production of "pipe in a pipe", "pipe in a form", the pre-insulated pipes products.
For anti-adhesive coating in molds. The mass fraction of non-volatile substances is not less than 45%.
For anti-adhesive coating in molds. Mass fraction of non-volatile substances not less than 60%.
Two-component system for the production of the "shell" of polyurethane foam with a density of the finished product 60 kg/m3 and above.
Component A - KAT-90 PPM, component B: Wannate PM-200 etc.
Two-component system for the SIP manufacture and sandwich panels of polyurethane foam with a density of the finished product not less than 55 kg/m3.
System for the PU foam structural elements production with a density of 80-120 kg/m3 in the finished product.
System for the PU foam structural elements production with a density of 200-300 kg/m3 in the finished product.
System for the polyurethane foam structural elements production with a density of 300-400 kg/m3 in the finished product.
System for the polyurethane foam structural elements production with a density of 400-600 kg/m3 in the finished product.
Non- foaming system designed to obtain fast – drying monolithic polyurethane.
